Contents

6.4.3.3 Packet Tracer – attach a Router to a LAN (Instructor Version)Part 1: screen Router InformationPart 2: Configure Router InterfacesPart 3: Verify the Configuration
*

6.4.3.3 Packet Tracer – connect a Router to a LAN


Part 1: display screen Router Information

Part 2: Configure Router Interfaces

Part 3: Verify the Configuration

Background

In this activity, you will use miscellaneous show commands to display screen the existing state the the router. You will certainly then usage the Addressing Table come configure router Ethernet interfaces. Finally, you will use regulates to verify and test your configurations.

You are watching: Which command displays the statistics for all interfaces configured on a router

Note: The routers in this task are partly configured. Few of the configurations room not covered in this course, however are detailed to assist you in making use of verification commands.

Note: The serial interfaces are already configured and also active. In addition, routing is configured utilizing EIGRP. This is excellent so the this task is (1) consistent with examples shown in the chapter, (2) prepared to carry out complete output from show commands when the college student configures and activates the Ethernet interfaces.

Part 1: display screen Router Information

Step 1: screen interface details on R1.

Note: Click a machine and then click the CLI tab to access the command heat directly. The console password is cisco. The privileged EXEC password is class.

a. I m sorry command displays the statistics for all interfaces configured top top a router?

R1#show interfacesb. Which command screens the information about the Serial 0/0/0 user interface only?

InstructionsWhat is the IP address on R1? there is no IP resolve configured ~ above the GigabitEthernet 0/0 interface.What is the MAC resolve of the GigabitEthernet 0/0 interface? 000d.bd6c.7d01What is the bandwidth on the GigabitEthernet 0/0 interface? 1000000 kbitsInstructions

R1#show interfaces gigabitEthernet 0/0GigabitEthernet0/0 is administratively down, heat protocol is under (disabled)Hardware is CN Gigabit Ethernet, resolve is 000d.bd6c.7d01 (bia 000d.bd6c.7d01)MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,reliability 255/255, txload 1/255, rxload 1/255Encapsulation ARPA, loopback no setKeepalive collection (10 sec)Full-duplex, 100Mb/s, media kind is RJ45output flow-control is unsupported, input flow-control is unsupportedARP type: ARPA, ARP Timeout 04:00:00,Last entry 00:00:08, output 00:00:05, output hang neverLast clearing that "show interface" counters neverInput queue: 0/75/0 (size/max/drops); total output drops: 0Queueing strategy: fifoOutput queue :0/40 (size/max)5 minute input price 0 bits/sec, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/sec0 packets input, 0 bytes, 0 no bufferReceived 0 broadcasts, 0 runts, 0 giants, 0 throttles0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort0 watchdog, 1017 multicast, 0 stop input0 entry packets v dribble problem detected0 packets output, 0 bytes, 0 underruns0 output errors, 0 collisions, 2 interface resets0 unknown protocol drops0 babbles, 0 so late collision, 0 deferred0 lost carrier, 0 no carrier0 output buffer failures, 0 output buffers swapped outStep 2: display a an overview list that the interfaces top top R1.a. Which command screens a brief an introduction of the current interfaces, statuses, and also IP addresses assigned come them?

R1#show ip interface briefb. Get in the command on each router and answer the adhering to questions:1) How countless serial interfaces room there on R1 and also R2? every router has actually 2 serial interfaces2) How numerous Ethernet interfaces room there top top R1 and also R2? R1 has 6 Ethernet interfaces and also R2 has actually 2 Ethernet interfaces. 3) space all the Ethernet interfaces on R1 the same? If no, define the difference(s). No they are not. There are two Gigabit Ethernet interfaces and also 4 fast Ethernet interfaces. Gigabit Ethernet interfaces assistance speeds of approximately 1,000,000,000 bits and Fast Ethernet interfaces assistance speeds of as much as 1,000,000 bits.

Step 3: display screen the routing table top top R1.

a. What command display screens the content of the routing table?

Part 2: Configure Router Interfaces

Step 1: Configure the GigabitEthernet 0/0 interface on R1.

a. Get in the following regulates to address and activate the GigabitEthernet 0/0 interface on R1 :

R1(config)# interface gigabitethernet 0/0R1(config-if)# ip address 192.168.10.1 255.255.255.0R1(config-if)# no shutdown%LINK-5-CHANGED: user interface GigabitEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: line protocol on user interface GigabitEthernet0/0, changed state come upb. The is great practice come configure a description for each user interface to help file the network information. Configure one interface summary indicating come which an equipment it is connected.

R1(config-if)# summary LAN link to S1c. R1 should now be able to ping PC1.

R1(config-if)# end%SYS-5-CONFIG_I: Configured indigenous console by consoleR1# ping 192.168.10.10Type escape succession to abort.Sending 5, 100-byte ICMP Echos to 192.168.10.10, timeout is 2 seconds:.!!!!Success price is 80 percent (4/5), round-trip min/avg/max = 0/2/8 msStep 2: Configure the continuing to be Gigabit Ethernet Interfaces on R1 and also R2.a. Usage the details in the Addressing Table to finish the interface configurations because that R1 and also R2. Because that each interface, carry out the following:

Enter the IP attend to and activate the interface.Configure an ideal description.

b. Verify user interface configurations.

See more: 5-7 Business Days From Today, Date And Day After 5 Days From Today

Step 3: back up the configurations to NVRAM.

Save the configuration documents on both routers come NVRAM. What command did friend use? copy operation start